Backhoe Warning Safety Sticker Part Numbers and Positions

This guide identifies the label designs included in our Large Backhoe Safety Sticker Kit, KIT-BH002, and explains how to use its general placement illustration.

The kit contains 42 decals across 29 designs. The codes below are our product identifiers, not verified equipment-manufacturer part numbers. Use your backhoe’s applicable operator and parts manuals to confirm the required wording, quantity, and location of each replacement label.

How to use the backhoe decal diagram

The illustration shows general label locations on a backhoe silhouette, with callouts for selected exterior labels and an inside-cab label list. It is not a verified factory decal map for a particular make, model, or serial-number range.

Compare each callout with your machine’s actual configuration and manufacturer’s decal-location instructions. Do not assume every illustrated location applies to your backhoe.

Before removing a worn label, photograph its wording and the surrounding area. If the label is missing, identify it from the applicable manual or ask the manufacturer or authorized dealer for help rather than relying on an adhesive outline.

General backhoe decal-placement illustration with product-code callouts and an inside-cab label list.

DANGER Vehicle Frequently Reversing Safety Sticker WARNING ROPS Fitted Do-Not Drill Or Weld Safety Sticker Warning Hot Surface Safety Sticker Crush Risk Clamp Arm Support Bracket To Lift Cylinder Rod Before Servicing Engine Area Warning Rotating Blades Safety Sticker Pressurized System Hot Coolant Can Cause Serious Burns Warning Crush Zone Safety Decal DANGER Keep Clear Of Stabilizers Safety Sticker DANGER Battery Fire Hazard Charge Batteries In Well Ventilated Area Safety Sticker Pressurized System Before Working On Machine Bleed Hydraulic Tank Pressure Safety Sticker Warning Use 3 Point Support Do Not Jump Off Machine Safety Sticker Backhoe Crush Hazard Do Not Stand Under Unsupported Load Safety Decal Operator’s Daily Responsibility Safety Sticker Call 811 Before You Dig Safety Sticker DANGER Hazardous Moving and Rotating Parts Do Not Enter Work Area Safety Sticker Outrigger Crush Hazard Safety Sticker Clamp Arm Support Bracket To Lift Cylinder Rod Before Servicing Engine Area Safety Sticker Do Not Use This Machine To Lift Loads Over Personnel Safety Sticker DANGER Be Aware Of Overhead Lines and Underground Utilities Safety Sticker DANGER Look Up And Live Keep Clear Of All Overhead Electrical Hazards Safety Sticker DANGER Clearance for Operating Equipment Near Power Lines Safety Sticker WARNING Seatbelts Must Be Worn Safety Label Driver Only No Passengers Safety Decal Mobile Phone Must Not Be Used While Operating Machine Safety Sticker Warning All Attachments Must Be Considered Part Of The Load Safety Sticker Read Operators Manual Thoroughly Before Operating Safety Sticker

Which backhoe sticker kit does this guide cover?

This article covers the Large Backhoe Safety Sticker Kit – 42 Decals, KIT-BH002.

Our Backhoe Safety Sticker Kit – 30 Warning & Maintenance Decals, KIT-BH001, is a different assortment. Compare the contents before ordering; the two kits do not contain identical selections or quantities.

Large-kit contents: 42 decals across 29 designs

The quantities below are the supplied decal quantities. Repeated designs account for the difference between 29 designs and 42 decals.

Crush, moving-parts, and support warnings

  • 4 × CBH-001: Keep Clear — Do Not Stand Under Unsupported Load, Frame, Boom or Stick.
  • 2 × CRSH-001: Hazardous Moving and Rotating Parts — Do Not Enter Work Area.
  • 1 × DNGR-003: Clamp Lift Arm Support Bracket Before Servicing.
  • 2 × DNGR-004: Danger Keep Clear.
  • 1 × DNGR-005: Do Not Use This Machine to Lift Loads Over Personnel.
  • 2 × WRN-005: Crush Zone.
  • 2 × WRN-006: Rotating Blades.
  • 2 × CO-001: Outriggers Will Cause Serious Crushing Injury — Stand Clear.

Electrical, utility, and digging warnings

  • 1 × DNGR-006: Underground Services and Overhead Wires.
  • 1 × DNGR-007: Look Up and Live — Overhead Electrical Hazards.
  • 1 × DNGR-008: Power Line Clearance Diagrams.
  • 1 × I-047: Call 811 Before You Dig.

Printed power-line distances are not universal clearance guidance. Follow the applicable requirements, utility instructions, and site-specific procedures.

Service and equipment warnings

Use each warning only where its wording matches the equipment and the manufacturer’s procedures. A sticker does not provide a support bracket, release pressure, isolate energy, or establish ROPS certification.

Operator and access reminders

  • 1 × DNGR-001: Vehicle Frequently Reversing.
  • 2 × WRN-007: Three Points of Contact During Entry and Exit.
  • 1 × WRN-011: Seatbelts Must Be Worn.
  • 1 × WRN-012: Driver Only — Strictly No Passengers.
  • 1 × WRN-013: No Mobile Phone Use While Operating.
  • 1 × WRN-014: Attachment Load and Quick Hitch Clearance.
  • 1 × I-048: Operator’s Daily Responsibility Checklist.
  • 1 × I-011B: Read Operators Manual Thoroughly Before Operating.
  • 1 × I-040: Inspect Machine Before Use.

Lubrication and fluid identification

  • 4 × I-035: Grease Here, with separate arrow pieces for installation.
  • 1 × I-006: Hydraulic Oil.
  • 1 × I-007: Diesel Fuel.

Identify the correct lubrication and fill points from the equipment documentation before applying these labels. A label should not be used to identify an unknown reservoir or establish a lubricant specification or service interval.

Confirm the required labels and locations

Before ordering, compare the included designs with your machine’s label list. Check the complete warning, symbols, language, dimensions, quantity, and specified mounting position.

Keep labels associated with the component or hazard they identify. Follow the manufacturer’s instructions and avoid covering controls, instruments, viewing areas, identification plates, or existing warnings.

Where the original location or required message is uncertain, resolve that question with the manufacturer or authorized dealer before treating the replacement as complete.

What the kit does—and does not—provide

KIT-BH002 is an assortment of warning, maintenance, and identification labels. It is not a guaranteed complete replacement set for every backhoe make or model.

Applying the kit does not establish equipment condition, load capacity, inspection approval, or certification. The labels do not replace guards, support devices, operating instructions, training, or equipment-specific procedures.

For different sizes, quantities, or label selections, contact us before ordering. Provide clear reference photos, dimensions, the required wording, and your machine’s make and model so we can discuss the label options.

Leave a comment (all fields required)

Comments will be approved before showing up.